1. Hello Guest, selamat datang di Forum WinPoin. Kamu bisa bertanya, berdiskusi, sharing, dan ngobrolin apapun seputar Windows, Windows Phone, PC, Gadget, atau hal seputar Teknologi lainnya. Selamat berkomunitas! ;)

Ask Dial Up

Discussion in 'Windows 8' started by said haris, Jun 7, 2015.

  1. said haris

    said haris Member

    Joined:
    Feb 28, 2015
    Messages:
    39
    apa penyebabnya tidak bisa membuat koneksi Dial Up .
     
  2. dst-nat

    dst-nat New Member

    Joined:
    Apr 26, 2015
    Messages:
    11
    penyebabnya ada banyak hal tergantung code error yang disampaikan

    The following list contains the error codes for dial-up connections or VPN connections:

    600
    An operation is pending.

    601
    The port handle is invalid.

    602
    The port is already open.

    603
    Caller's buffer is too small.

    604
    Wrong information specified.

    605
    Cannot set port information.

    606
    The port is not connected.

    607
    The event is invalid.

    608
    The device does not exist.

    609
    The device type does not exist.

    610
    The buffer is invalid.

    611
    The route is not available.

    612
    The route is not allocated.

    613
    Invalid compression specified.

    614
    Out of buffers.

    615
    The port was not found.

    616
    An asynchronous request is pending.

    617
    The port or device is already disconnecting.

    618
    The port is not open.

    619
    The port is disconnected.

    620
    There are no endpoints.

    621
    Cannot open the phone book file.

    622
    Cannot load the phone book file.

    623
    Cannot find the phone book entry.

    624
    Cannot write the phone book file.

    625
    Invalid information found in the phone book.

    626
    Cannot load a string.

    627
    Cannot find key.

    628
    The port was disconnected.

    629
    The port was disconnected by the remote machine.

    630
    The port was disconnected due to hardware failure.

    631
    The port was disconnected by the user.

    632
    The structure size is incorrect.

    633
    The port is already in use or is not configured for Remote Access dialout.

    634
    Cannot register your computer on the remote network.

    635
    Unknown error.

    636
    The wrong device is attached to the port.

    637
    The string could not be converted.

    638
    The request has timed out.

    639
    No asynchronous net available.

    640
    A NetBIOS error has occurred.

    641
    The server cannot allocate NetBIOS resources needed to support the client.

    642
    One of your NetBIOS names is already registered on the remote network.

    643
    A network adapter at the server failed.

    644
    You will not receive network message popups.

    645
    Internal authentication error.

    646
    The account is not permitted to log on at this time of day.

    647
    The account is disabled.

    648
    The password has expired.

    649
    The account does not have Remote Access permission.

    650
    The Remote Access server is not responding.

    651
    Your modem (or other connecting device) has reported an error.

    652
    Unrecognized response from the device.

    653
    A macro required by the device was not found in the device .INF file section.

    654
    A command or response in the device .INF file section refers to an undefined macro

    655
    The <message> macro was not found in the device .INF file section.

    656
    The <defaultoff> macro in the device .INF file section contains an undefined macro

    657
    The device .INF file could not be opened.

    658
    The device name in the device .INF or media .INI file is too long.

    659
    The media .INI file refers to an unknown device name.

    660
    The device .INF file contains no responses for the command.

    661
    The device .INF file is missing a command.

    662
    Attempted to set a macro not listed in device .INF file section.

    663
    The media .INI file refers to an unknown device type.

    664
    Cannot allocate memory.

    665
    The port is not configured for Remote Access.

    666
    Your modem (or other connecting device) is not functioning.

    667
    Cannot read the media .INI file.

    668
    The connection dropped.

    669
    The usage parameter in the media .INI file is invalid.

    670
    Cannot read the section name from the media .INI file.

    671
    Cannot read the device type from the media .INI file.

    672
    Cannot read the device name from the media .INI file.

    673
    Cannot read the usage from the media .INI file.

    674
    Cannot read the maximum connection BPS rate from the media .INI file.

    675
    Cannot read the maximum carrier BPS rate from the media .INI file.

    676
    The line is busy.

    677
    A person answered instead of a modem.

    678
    There is no answer.

    679
    Cannot detect carrier.

    680
    There is no dial tone.

    681
    General error reported by device.

    682
    ERROR WRITING SECTIONNAME

    683
    ERROR WRITING DEVICETYPE

    684
    ERROR WRITING DEVICENAME

    685
    ERROR WRITING MAXCONNECTBPS

    686
    ERROR WRITING MAXCARRIERBPS

    687
    ERROR WRITING USAGE

    688
    ERROR WRITING DEFAULTOFF

    689
    ERROR READING DEFAULTOFF

    690
    ERROR EMPTY INI FILE

    691
    Access denied because username and/or password is invalid on the domain.

    692
    Hardware failure in port or attached device.

    693
    ERROR NOT BINARY MACRO

    694
    ERROR DCB NOT FOUND

    695
    ERROR STATE MACHINES NOT STARTED

    696
    ERROR STATE MACHINES ALREADY STARTED

    697
    ERROR PARTIAL RESPONSE LOOPING

    698
    A response keyname in the device .INF file is not in the expected format.

    699
    The device response caused buffer overflow.

    700
    The expanded command in the device .INF file is too long.

    701
    The device moved to a BPS rate not supported by the COM driver.

    702
    Device response received when none expected.

    703
    ERROR INTERACTIVE MODE

    704
    ERROR BAD CALLBACK NUMBER

    705
    ERROR INVALID AUTH STATE

    706
    ERROR WRITING INITBPS

    707
    X.25 diagnostic indication.

    708
    The account has expired.

    709
    Error changing password on domain.

    710
    Serial overrun errors were detected while communicating with your modem.

    711
    RasMan initialization failure. Check the event log.

    712
    Biplex port is initializing. Wait a few seconds and redial.

    713
    No active ISDN lines are available.

    714
    Not enough ISDN channels are available to make the call.

    715
    Too many errors occurred because of poor phone line quality.

    716
    The Remote Access IP configuration is unusable.

    717
    No IP addresses are available in the static pool of Remote Access IP addresses.

    718
    PPP timeout.

    719
    PPP terminated by remote machine.

    720
    No PPP control protocols configured.

    721
    Remote PPP peer is not responding.

    722
    The PPP packet is invalid.

    723
    The phone number, including prefix and suffix, is too long.

    724
    The IPX protocol cannot dial-out on the port because the computer is an IPX router.

    725
    The IPX protocol cannot dial-in on the port because the IPX router is not installed.

    726
    The IPX protocol cannot be used for dial-out on more than one port at a time.

    727
    Cannot access TCPCFG.DLL.

    728
    Cannot find an IP adapter bound to Remote Access.

    729
    SLIP cannot be used unless the IP protocol is installed. 730
    Computer registration is not complete.

    731
    The protocol is not configured.

    732
    The PPP negotiation is not converging.

    733
    The PPP control protocol for this network protocol is not available on the server.

    734
    The PPP link control protocol terminated..

    735
    The requested address was rejected by the server..

    736
    The remote computer terminated the control protocol.

    737
    Loopback detected..

    738
    The server did not assign an address.

    739
    The remote server cannot use the Windows NT encrypted password.

    740
    The TAPI devices configured for Remote Access failed to initialize or were not installed correctly.

    741
    The local computer does not support encryption.

    742
    The remote server does not support encryption.

    743
    The remote server requires encryption.

    744
    Cannot use the IPX net number assigned by the remote server. Check the event log.

    745
    ERROR_INVALID_SMM

    746
    ERROR_SMM_UNINITIALIZED

    747
    ERROR_NO_MAC_FOR_PORT

    748
    ERROR_SMM_TIMEOUT

    749
    ERROR_BAD_PHONE_NUMBER

    750
    ERROR_WRONG_MODULE

    751
    The callback number contains an invalid character. Only the following 18 characters are allowed: 0 to 9, T, P, W, (, ), -, @, and space

    752
    A syntax error was encountered while processing a script.

    753
    The connection could not be disconnected because it was created by the multi-protocol router.

    754
    The system could not find the multi-link bundle.

    755
    The system cannot perform automated dial because this connection has a custom dialer specified.

    756
    This connection is already being dialed.

    757
    Remote Access Services could not be started automatically. Additional information is provided in the event log.

    758
    Internet Connection Sharing is already enabled on the connection.

    759
    An error occurred while the existing Internet Connection Sharing settings were being changed.

    760
    An error occurred while routing capabilities were being enabled.

    761
    An error occurred while Internet Connection Sharing was being enabled for the connection.

    762
    An error occurred while the local network was being configured for sharing.

    763
    Internet Connection Sharing cannot be enabled. There is more than one LAN connection other than the connection to be shared.

    764
    No smart card reader is installed.

    765
    Internet Connection Sharing cannot be enabled. A LAN connection is already configured with the IP address that is required for automatic IP addressing.

    766
    A certificate could not be found. Connections that use the L2TP protocol over IPSec require the installation of a machine certificate, also known as a computer certificate.

    767
    Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network has more than one IP address configured. Please reconfigure the LAN connection with a single IP address before enabling Internet Connection Sharing.

    768
    The connection attempt failed because of failure to encrypt data.

    769
    The specified destination is not reachable.

    770
    The remote computer rejected the connection attempt.

    771
    The connection attempt failed because the network is busy.

    772
    The remote computer's network hardware is incompatible with the type of call requested.

    773
    The connection attempt failed because the destination number has changed.

    774
    The connection attempt failed because of a temporary failure. Try connecting again.

    775
    The call was blocked by the remote computer.

    776
    The call could not be connected because the remote computer has invoked the Do Not Disturb feature.

    777
    The connection attempt failed because the modem (or other connecting device on the remote computer is out of order.

    778
    It was not possible to verify the identity of the server.

    779
    To dial out using this connection you must use a smart card.

    780
    An attempted function is not valid for this connection.

    781
    The connection requires a certificate, and no valid certificate was found. For further assistance, click More Info or search Help and Support Center for this error number.

    782
    Internet Connection Sharing (ICS and Internet Connection Firewall (ICF cannot be enabled because Routing and Remote Access has been enabled on this computer. To enable ICS or ICF, first disable Routing and Remote Access. For more information about Routing and Remote Access, ICS, or ICF, see Help and Support.

    783
    Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network is either not present, or is disconnected from the network. Please ensure that the LAN adapter is connected before enabling Internet Connection Sharing.

    784
    You cannot dial using this connection at logon time, because it is configured to use a user name different than the one on the smart card. If you want to use it at logon time, you must configure it to use the user name on the smart card.

    785
    You cannot dial using this connection at logon time, because it is not configured to use a smart card. If you want to use it at logon time, you must edit the properties of this connection so that it uses a smart card.

    786
    The L2TP connection attempt failed because there is no valid machine certificate on your computer for security authentication.

    787
    The L2TP connection attempt failed because the security layer could not authenticate the remote computer.

    788
    The L2TP connection attempt failed because the security layer could not negotiate compatible parameters with the remote computer.

    789
    The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer.

    790
    The L2TP connection attempt failed because certificate validation on the remote computer failed.

    791
    The L2TP connection attempt failed because security policy for the connection was not found.

    792
    The L2TP connection attempt failed because security negotiation timed out.

    793
    The L2TP connection attempt failed because an error occurred while negotiating security.

    794
    The Framed Protocol RADIUS attribute for this user is not PPP.

    795
    The Tunnel Type RADIUS attribute for this user is not correct.

    796
    The Service Type RADIUS attribute for this user is neither Framed nor Callback Framed.

    797
    A connection to the remote computer could not be established because the modem was not found or was busy. For further assistance, click More Info or search Help and Support Center for this error number.

    798
    A certificate could not be found that can be used with this Extensible Authentication Protocol.

    799
    Internet Connection Sharing (ICS cannot be enabled due to an IP address conflict on the network. ICS requires the host be configured to use 192.168.0.1. Please ensure that no other client on the network is configured to use 192.168.0.1.

    800
    Unable to establish the VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection.

    801
    This connection is configured to validate the identity of the access server, but Windows cannot verify the digital certificate sent by the server.

    802
    The card supplied was not recognized. Please check that the card is inserted correctly, and fits tightly.

    803
    The PEAP configuration stored in the session cookie does not match the current session configuration.

    804
    The PEAP identity stored in the session cookie does not match the current identity.

    805
    You cannot dial using this connection at logon time, because it is configured to use logged on user's credentials.

    900
    The router is not running.

    901
    The interface is already connected.

    902
    The specified protocol identifier is not known to the router.

    903
    The Demand-dial Interface Manager is not running.

    904
    An interface with this name is already registered with the router.

    905
    An interface with this name is not registered with the router.

    906
    The interface is not connected.

    907
    The specified protocol is stopping.

    908
    The interface is connected and hence cannot be deleted.

    909
    The interface credentials have not been set.

    910
    This interface is already in the process of connecting.

    911
    An update of routing information on this interface is already in progress.

    912
    The interface configuration in invalid. There is already another interface that is connected to the same interface on the remote router.

    913
    A Remote Access Client attempted to connect over a port that was reserved for Routers only.

    914
    A Demand Dial Router attempted to connect over a port that was reserved for Remote Access Clients only.

    915
    The client interface with this name already exists and is currently connected.

    916
    The interface is in a disabled state.

    917
    The authentication protocol was rejected by the remote peer.

    918
    There are no authentication protocols available for use.

    919
    The remote computer refused to be authenticated using the configured authentication protocol. The line has been disconnected.

    920
    The remote account does not have Remote Access permission.

    921
    The remote account has expired.

    922
    The remote account is disabled.

    923
    The remote account is not permitted to logon at this time of day.

    924
    Access was denied to the remote peer because username and/or password is invalid on the domain.

    925
    There are no routing enabled ports available for use by this demand dial interface.

    926
    The port has been disconnected due to inactivity.

    927
    The interface is not reachable at this time.

    928
    The Demand Dial service is in a paused state.

    929
    The interface has been disconnected by the administrator.

    930
    The authentication server did not respond to authentication requests in a timely fashion.

    931
    The maximum number of ports allowed for use in the multilinked connection has been reached.

    932
    The connection time limit for the user has been reached.

    933
    The maximum limit on the number of LAN interfaces supported has been reached.

    934
    The maximum limit on the number of Demand Dial interfaces supported has been reached.

    935
    The maximum limit on the number of Remote Access clients supported has been reached.

    936
    The port has been disconnected due to the BAP policy.

    937
    Because another connection of your type is in use, the incoming connection cannot accept your connection request.

    938
    No RADIUS servers were located on the network.

    939
    An invalid response was received from the RADIUS authentication server. Make sure that the case sensitive secret password for the RADIUS server is set correctly.

    940
    You do not have permission to connect at this time.

    941
    You do not have permission to connect using the current device type.

    942
    You do not have permission to connect using the selected authentication protocol.

    943
    BAP is required for this user.

    944
    The interface is not allowed to connect at this time.

    945
    The saved router configuration is incompatible with the current router.

    946
    RemoteAccess has detected older format user accounts that will not be migrated automatically. To migrate these manually, run XXXX.

    948
    The transport is already installed with the router.

    949
    Received invalid signature length in packet from RADIUS server.

    950
    Received invalid signature in packet from RADIUS server.

    951
    Did not receive signature along with EAPMessage from RADIUS server.

    952
    Received packet with invalid length or Id from RADIUS server.

    953
    Received packet with attribute with invalid length from RADIUS server.

    954
    Received invalid packet from RADIUS server.

    955
    Authenticator does not match in packet from RADIUS server.

    source : https://support.microsoft.com/en-us/kb/824864
     
    • Setuju Setuju x 1

Share This Page